Jump to Navigation

Honeywell 10260S Herculine® Smart Actuator

Herculine® Smart Actuator
10260S

Honeywell’s HercuLine® 10260S Smart actuators incorporate all of the high quality and reliable features of the traditional HercuLine® actuators plus the added benefits of a microprocessor-based enhanced electronics unit (EEU).

These additional benefits provide:
     Faster set-up and commissioning
     Network capability
     Health parameter monitoring for proactive maintenance planning. 

HercuLine 10260S Smart actuators enable operation at maximum process efficiency, minimal downtime, and access to all actuator parameters for real-time business decisions.

Honeywell’s 10260S actuators are industrial rated and engineered for very precise positioning of dampers and valves. The HercuLine 10260S performs especially well in extremely demanding environments requiring continuous duty, high reliability, and low maintenance. Typical applications are furnace pressure dampers, gas/air valves, windbox dampers, coal mill dampers, and more.

• Duty Cycle – Continuous duty cycle motor. No burn out.
• Power Requirements – Low power consumption 120/240 Vac, 50/60 Hz, single phase < 1 Amp.
• Enclosure – Rugged, industrial grade enclosure.
• Low Maintenance – Simple-proven design means high reliability/low maintenance.
• Enclosure – Rugged, industrial grade enclosure.
• Low Maintenance – Simple-proven design means high reliability/low maintenance.
• Limit Switches – Two end-of-travel electric limit switches are supplied as standard equipment with all 10260S       series actuators.
• Warranty – Exceptional warranty
• Certification – CSA, UL (Future) CE available.

Select a link under the "item" tab below to order.

Table 1
XXXXXX
Table 1KEY NUMBER - Torque and Speed
Output Torque
(lb. - ft.) (N - M) 50 Hz
10261S10 (15) 10
10262S20 (27) 20
10264S40 (55) 40
10266S60 (80) 60
10267S40 (55) 20
10268S80 (110) 40
10269S150 (200) 60
10263S200 (270) 40
10265S300 (400) 60
Physical:
Weight: 45 lb. (20.4 kg) net
Enclosure: Precision-machined Aluminum alloy casting, finished in light gray powder coat epoxy.
Mechanical Stops: To prevent over-travel.
Operating Temperature: –30 °C to +75 °C (–20 °F to +170 °F)
Storage Temperature: –40 °C to +93 °C (–40 °C to +200 °F)
Relative Humidity: 0 to 99 % R.H. non-condensing over the full operating temperature range.
Scale: 0 % to 100 % corresponding to full crank arm travel.
Crank Arm: Adjustable radii (1-7/16" to a maximum of 5"). Position adjustable through 360° rotation. Optional 12" crank arm adjustable 0 to 12" radii.
Rotation: 90° degrees between 0 % and 100 % on scale, limited by mechanical stops.
Direction of Rotation: Field selectable via HMI.
Manual Handwheel: Provides a means of positioning the actuator in the event of a power failure or set-up.
Lubrication: Texaco Starplex 2 EP Grease
Electrical:
Output Torque/Full Travel Stroking Time: Model # Torque Output Shaft Speed sec/90°
10261S
10262S
10264S
10266S
10267S
10268S
10269S
10263S
10265S		 Lb-ft N-M @60Hz @50Hz
10
20
40
60
40
80
150
200
300		 15
27
55
80
55
110
200
270
400		 10
20
40
20
40
60
40
60		 12
24
48
72
24
48
72
48
72
Mains Supply: 120 Vac single phase, 50 or 60 Hz 240 Vac single phase, 50 or 60 Hz
Motor: Instant start/stop, non-coasting, non-burnout, continuous duty, permanent magnet, synchronous induction motor. Can be stalled up to 100 hours without damage.
Fuses (Motor drive): Wickmann USA #373-1160-0-41: 1.6 Amp Fast (2)
Loss of Power: Stays in place.
Local Auto/Manual Switch: Optional – Allows local and automatic operation of the actuator.
Limit Switches: Standard – Two SPDT end of travel limits.
Certifications:
Approvals: CE Compliance (Optional)
CSA/UL
NEMA 4
Torque Settings of Crank Arm Bolts:
Clamp Bolt: Standard Arm (Part Number 087449) (1-7/16 to 5 in. adjustment): 85 lb-ft. Optional Long Arm (Part Number 154007) (0 to 12 in. adjustment): 85 lb-ft.
Rod End Bolt: Standard and long arms: 30-35 lb./ft


Main menu 2