Jump to Navigation

Johnson Controls M9210-xxx-3 Electric Spring Return Actuator

Electric Spring Return Actuator
M9210-xxx-3

The M9210-xxx-3 Actuators are direct mount, spring return electric actuators that operate with these available power options:

• AC 24 V at 50/60 Hz or DC 24 V (AGx, BGx, GGx, HGx)
• AC 120 V at 60 Hz (BAx)
• AC 230 V at 50/60 Hz (BDx)

These bidirectional actuators do not require a damper linkage, and are easily installed on dampers with 1/2 to 3/4 in. or 12 to 19 mm round shafts, or 3/8 and 1/2 in. or 10, 12, and 14 mm square shafts using the standard shaft clamp included with the actuator. An optional M9220-600 Jackshaft Coupler Kit is available for 3/4 to 1-1/16 in. or 19 to 27 mm round shafts, or 5/8 and 3/4 in. or 16, 18, and 19 mm square shafts. The M9210-xxx-3 Electric Spring Return Actuators provide running and spring return torques of 89 lb·in (10 N·m). Integral line voltage auxiliary switches are available on the xxC models to indicate end-stop position, or to perform switching functions within the selected rotation range.

• reversible mounting design — simplifies installation and enables the actuator to spring return in either direction
• removable coupler — adapts to a shorter damper shaft
• electronic stall detection throughout entire rotation range — extends the life of the actuator by deactivating the actuator motor when an overload condition is detected
• integral 48 in. (1.2 m) halogen-free cables with colored and numbered conductors — simplify field wiring
• integral auxiliary switches (xxC models) — provide one fixed and one adjustable switch point with line voltage capability
• NEMA 2 (IP54) rated aluminum enclosure — protects the internal components of the actuator from dirt and moisture
• easy-to-use locking manual override with auto release and crank storage — allows for manual positioning of the actuator hub
• integral connectors for 3/8 in. (10 mm) flexible metal conduit — simplify installation and field wiring
• microprocessor-controlled brushless DC motor (-AGx, -GGx, and -HGx) types — provides constant run-time independent of torque

Select a link under the "item" tab below to order.

Cat #Auxiliary SwitchControl TypePower Requirements
M9210-AGA-3NoneFloatingAC 24 V at 50/60 Hz or DC 24 V
M9210-AGC-3TwoFloatingAC 24 V at 50/60 Hz or DC 24 V
M9210-BAA-3NoneOn/OffAC 120 V at 60 Hz
M9210-BAC-3TwoOn/OffAC 120 V at 60 Hz
M9210-BDA-3NoneOn/OffAC 230 V at 50/60 Hz
M9210-BDC-3TwoOn/OffAC 230 V at 50/60 Hz
M9210-BGA-3NoneOn/OffAC 24 V at 50/60 Hz or DC 24 V
M9210-BGC-3TwoOn/OffAC 24 V at 50/60 Hz or DC 24 V
M9210-GGA-3NoneProportionalAC 24 V at 50/60 Hz or DC 24 V
M9210-GGC-3TwoProportionalAC 24 V at 50/60 Hz or DC 24 V
M9210-HGA-3NoneProportional w/Adjustable Zero and SpanAC 24 V at 50/60 Hz or DC 24 V
M9210-HGC-3TwoProportional w/Adjustable Zero and SpanAC 24 V at 50/60 Hz or DC 24 V
Power Requirements AGx, GGx, HGx Models AC 24 V (19.2 to 30 V) at 50/60 Hz: Class 2, 9.6 VA Running,
6 VA Holding Position;
DC 24 V (21.6 to 26.4 V); Class 2, 3.9 W Running, 2.1 W Holding Position
BAx Models AC 120 V (AC 102 to 132 V) at 60 Hz: 0.25 A Running, 0.13 A Holding Position
BDx Models AC 230 V (AC 198 to 264 V) at 50/60 Hz: 0.15 A Running, 0.09 A Holding Position
BGx Models AC 24 V (19.2 to 30 V) at 50/60 Hz: Class 2, 17.7 VA Running,
5.1 VA Holding Position;
DC 24 V (21.6 to 26.4 V): Class 2, 15.6 W Running, 2.6 W Holding Position
Transformer Sizing Requirements AGx, GGx, HGx Models 15 VA Minimum per Actuator
Bxx Models 25 VA Minimum per Actuator
Input Signal AGx Models DC 0 (2) to 10 V or 0 (4) to 20 mA with Field Furnished 500 ohm resistor;
Switch Selectable Direct or Reverse Action with Signal Increase, 500 ms minimum pulse
width
GGx Models Factory Set at DC 0 to 10 V, CW Rotation with Signal Increase;
Selectable DC 0 (2) to 10 V or 0 (4) to 20 mA with Field Furnished
500 ohm, 0.25 W minimum resistor;
Switch Selectable Direct or Reverse Action with Signal Increase
HGx Models Factory Set DC 0 to 10 V, CW Rotation with Signal Increase;
Selectable DC 0 to 10 V or 0 to 20 mA with Field Furnished 500 ohm,
0.25 W minimum resistor;
Start Point Programmable DC 0 to 10 V;
Span Programmable DC 2 to 10 V; Switch Selectable Direct or Reverse Action with Signal
Increase
Input Signal Adjustments GGx Models Factory Set at DC 0 to 10 V, CW Rotation with Signal Increase; Selectable DC 0 (2) to 10 V or
0 (4) to 20 mA with Field Furnished 500 ohm, 0.25 W Minimum Resistor; Switch Selectable Direct or
Reverse Action with Signal Increase
Control Input Impedance GGx, HGx Models Voltage Input: 200,000 ohms;
Current Input: 500 ohms with Field Furnished 500 ohm Resistor
Feedback Signal HGx Models DC 0 to 10 V for Desired Rotation Range up to 90°;
Corresponds to Rotation Limits, 1 mA maximum
GGx Models DC 0 (2) to 10 V for Desired Rotation Range up to 90°;
Corresponds to Rotation Limits, 1 mA maximum
Auxiliary Switch Rating xxC Models Two Single-Pole, Double-Throw (SPDT), Double-Insulated Switches with Gold Flash
Contacts:
AC 24 V, 50 VA Pilot Duty;
AC 120 V, 5.8 A Resistive, 1/4 hp, 275 VA Pilot Duty;
AC 240 V, 5.0 A Resistive, 1/4 hp, 275 VA Pilot Duty
Running Torque   89 lb·in (10 N·m)
Rotation Range   Adjustable from 30 to 90° CW or CCW with Optional
M9210-603 Adjustable Stop Kit; Mechanically Limited to 90°
Cycles   60,000 Full Stroke Cycles, 1,500,000 repositions
Electrical Connections Actuator
(All Models)
48 in. (1.2 m) Halogen-Free Cable with 18 AWG (0.75 mm2) Wire Leads
Auxiliary Switches
(GGC Models)
48 in. (1.2 m) Halogen-Free Cable with 18 AWG (0.75 mm2) Wire Leads
Conduit Connections   Integral Connectors for 3/8 in. (10 mm) Flexible Metal Conduit
Aluminum Enclosure   NEMA 2 (IP54) for All Mounting Orientations
Compliance North America UL Listed, File E27734, CCN XAPX (United States) and XAPX7 (Canada)
Europe CE Mark, EMC Directive 89/336/EEC (M9210-xGA-3 Models)
CE Mark, Low Voltage Directive 73/23/EEC
(M9210-BDA-3 and M9210-xxC-3 Models)
Shipping Weight xGx Models 6.4 lb (2.9 kg)
BAx and BDx Models 7.6 lb (3.5 kg)


Main menu 2

about seo