Jump to Navigation

Johnson Controls M9106 Series Electric Non-spring Return Actuators

Electric Non-spring Return Actuators
M9106 Series

The M9106-xGx-2 Series direct-mount electric actuators operate on 24 VAC power and are available for use with on-off, floating, or proportional controllers. These non-spring return actuators are easily installed on a Variable Air Volume (VAV) box, a damper with a round shaft up to 1/2 inch (13 mm) in diameter or a square shaft up to 3/8 inch (10 mm).

The M9106 models have 53 lb·in (6 N·m) running torque. They have a nominal 60-second travel time for 90° of rotation at 60 Hz (72 seconds at 50 Hz) with a load-independent rotation time. The M9106-xGC-2 models are available with integral auxiliary switches to perform switching functions at any angle within the selected rotation range. GGx models feature 0 to 10 VDC position feedback, and the AGF models provide 10,000 ohm position feedback.

• 35 dBA rating meets audible requirements for open ceilings
• synchronous drive provides constant rotation time that is independent of load
• direct shaft mount with single-screw coupler simplifies installation and provides 3-point shaft gripping
• magnetic clutch provides torque protection for the damper and actuator
• field-selectable rotation time (IGx models only) replaces M9104, EDA-2040, and ATP-2040 actuators and provides optimum rotation time for the specific application
• jumper-selectable rotation direction (GGx models only) simplifies installation
• adjustable rotation stops allow application versatility with 30 to 90° clockwise or counterclockwise rotation

Select a link under the "item" tab below to order.

Cat #On/Off ControlFloating ControlProportional Control10,000 ohm Potentiometer0 to 10 VDC Feedback2 Auxiliary SwitchesAdjustable Rotation Time
M9106-AGA-2Yes
M9106-AGC-2YesYes
M9106-AGF-2YesYes
M9106-GGA-2YesYes
M9106-GGC-2YesYesYes
M9106-IGA-2YesYesYes
M9106-IGC-2YesYesYesYes
Power Requirements AGx: (20 to 30 VAC) at 50/60 Hz; 2.5 VA supply, Class 2
IGx: (20 to 30 VAC) at 50/60 Hz; 2.8 VA supply, Class 2
GGx: (20 to 30 VAC) at 50/60 Hz; 3.2 VA supply, Class 2
Input Signal AGx and IGx: 20 to 30 VAC at 50/60 Hz
GGx: 0 to 10 VDC or 0 to 20 mA
Input Signal Adjustments 2AGx and IGx: CW and COM Terminals, CW rotation; CCW and COM Terminals, CCW rotation
GGx (Voltage Input or Current Input):
Jumper Selectable: 0 (2) to 10 VDC or 0 (4) to 20 mA
Factory Setting: 0 to 10 VDC, CW rotation with signal increase
Action is jumper selectable Direct (CW) or Reverse (CCW) with signal increase.
Input Impedance AGx: 200 ohms, nominal
IGx: 160 ohms, nominal
GGx: Voltage Input, 150,000 ohms; Current Input, 500 ohms
Feedback Signal AGF: 10,000 ohm potentiometer, 1 W
GGx: 0 to 10 VDC or 2 to 10 VDC for 90° (10 VDC at 1 mA);
Corresponds to input signal span selection
Auxiliary Switch Rating xGC: Two Single-Pole, Double-Throw (SPDT) switches rated at 24 VAC, 1.5 A inductive, 3.0 A resistive, 35 VA maximum per
switch, Class 2
Mechanical Output
(Running Torque)
1, 1.5, and 2 min. settings: 53 lb·in (6 N·m)
5.5 and 11 min. settings: 35 lb·in (4 N·m)
Cycles 100,000 full cycles; 2,500,000 repositions rated at 53 lb·in (6 N·m)
Audible Noise Rating 35 dBA maximum at 1 m
Rotation Range Adjustable from 30 to 90°, CW or CCW
Rotation Time IGx: Adjustable with switch settings (factory set for 1 min.)
60, 90, 120, 330, or 660 sec (1, 1.5, 2, 5.5 or 11 min.) at 60 Hz and
72, 108, 144, 396, or 792 sec at 50 Hz
All Other Models: Nominal 60 seconds at 60 Hz and 72 seconds at 50 Hz for 90°
Electrical Connection 1/4 in. spade terminals (To order optional pluggable terminal blocks, see Accessories chart.)
Mechanical Connection 3/8 to 1/2 in. (10 to 12.7 mm) round shaft or 3/8 in. (10 mm) square shaft
Enclosure NEMA 2, IP32
Ambient Operating Conditions -4 to 125°F (-20 to 52°C); 90% RH maximum, non-condensing
Ambient Storage Conditions IGx: -40 to 186°F (-40 to 86°C); 90% RH maximum, non-condensing
All Other Models: -40 to 176°F (-40 to 80°C); 90% RH maximum, non-condensing
Dimensions (H x W x D) 5.9 x 4.2 x 2.64 in. (150.1 x 106.5 x 67.0 mm)
Shipping Weight 2.4 lb (1.08 kg)
Agency Compliance UL 873 Listed, File E27734, CCN XAPX
CSA C22.2 No. 139 Certified, File LR85083, Class 3221 02
CE Mark, EMC Directive 89/336/EEC


Main menu 2