Jump to Navigation

Honeywell XYR3000 D/E Series Wireless Modems

Wireless Modems
XYR3000 D/E Series

The XYR300D Wireless Serial Radio Modem product provides RS232 or RS485 connections by radio. It is a low cost wireless alternative for linking PLC data loggers, supervisory computers, and intelligent transducers.

The XYR300D has been designed to be easy to use and simple to install. It uses a 900MHz spread spectrum radio which does not require a radio license in many countries.

The Module is fully integrated with radio, power supply, serial ports and microprocessor controller housed in a strong industrial aluminum case. XYR300E The XYR300E Wireless Ethernet Modem product is an ideal solution for Ethernet and serial connections in process control and automation applications – PLC’s, DCS, SCADA, data acquisition, wireless video. The XYR300E can handle multiple applications simultaneously.

• Improve Product Quality
• Ensure High Uptime
• Reduce Maintenance and Operational Costs
• Meet Regulatory Requirements
• Enhance Flexibility

Select a link under the "item" tab below to order.

Cat #DescriptionsTypeOrder Item
XYR300G-MModbus GatewayGatewaysWHG300GM
XYR300G-EEthernet GatewayGatewaysWHG300GE
XYR300DWireless Serial Radio ModemModemsWHS300D
XYR300EWireless Ethernet ModemModemsWHS300E
XYR400EWiFi Wireless Ethernet ModemModemsWHS400E
GENERAL   
  XYR300D
Wireless Serial Radio Modem
XYR400E
WiFiWireless Ethernet
Modem
XYR300E
 Wireless Ethernet Modem
Temperature: -40 to +140 deg F  
(-40 to +60 deg C)
-30 to +140 deg F  
(-35 to +60 deg C)
-40 to +140 deg F  
(-40 to +60 deg C)
Humidity: 0 – 99% 0 – 99% 0 – 99%
Approvals:
EMC Compliant FCC Part 15 Class A FCC 15.247, CE ETS 300 328, RSS210 FCC 15.247, RS21
Housing: DIN-rail Extruded Aluminum Case Removable terminal blocks for ease of module replacement. Terminals suitable for 12 gauge (2.5 sq mm) wire. DIN-rail Heavy Duty Painted Aluminum Case DIN-rail Heavy Duty Painted Aluminum Case
Dimensions: 114 x 185 x 30mm (4.5 x 7.3 x 1.2 inches) 114 x 140 x 30mm (4.5 x 5.5 x 1.2 inches) 114 x 140 x 30mm (4.5 x 5.5 x
1.2 inches)
LED Indication: For unit OK, radio Tx and Rx, serial Tx and Rx, DCD (comms OK) Power/OK, Radio Tx and Rx, Radio link, LAN Link/Activity, Serial Activity, Digital I/O Power/OK, Radio Tx and Rx, Radio link, LAN Link/Activity, Serial Activity, Digital I/O, LAN10/100Mbit Link

Radio Transceiver:

 

Frequency Hopping spread spectrum 902 – 928 Mhz

Transmit Power 1W

Approved to FCC Part 15 Cass A and FCC Part 15.247

Maximum Line-of-sight  range: 20 miles (4W ERP) depending on local conditions.

Range may be extended by using up to five intermediate repeater units in Controlled mode – unlimited repeaters in transparent mode.

RF Data Transmission Rate: 19200 baud , 57600 baud, 115200 baud (selectable)

Direct Sequence Spread Spectrum [DSSS] 2.400 – 2.484GHz, 13 selectable zones

Transmit Power: 100mW (20dBm) / 300mW (25dBm)

Receiver sensitivity: < 8% FER 96dBm @ 1Mb/s
91dBm @ 11Mb/s

Radio Range: 3 miles /5 km @ 300mW Line-of-sight range using high gain antennas with (4W ERP)
Range may be extended by using repeater features.

Dual SMA coaxial antenna connectors for antenna diversity

Frequency Hopping spread
spectrum 902 – 928 Mhz

Transmit Power 0.1 - 1W (20 – 30 dBm configurable

System Gain:140dB

Receiver sensitivity: -108
dBm @ 10-6 BER

Data Rates: 19.2, 38.4, 100, 200 Kb/s or auto-rate
selection

Protocol: CSMA/CA with 32 bit CRC and auto-correction

Radio Range: 60 miles /100 km Line-of-sight range using high gain antennas with (4W ERP)

Range may be extended by using repeater features.

I/O Capacity: Input and Output buffers 2Kbyte  Discreet I/O; Input voltage free contact / Output FET 30VDC 500 mA. Used to transfer input to output status or ommunications failure output One I/O channel, Input voltage- free contact / Output FET 30VDC 500 mA. Used to transfer input to output status or communications failure output
Power Supply: 10 – 30 Vdc or 10 – 24 Vac 9 – 30Vdc 10 – 30Vdc
Serial Port: Standard data rates 1200 to 115200 baud

RS232 and RS485 standard interface connections provided. Each connected to the same serial point. Serial interfaces are asynchronous non- eturn-zero (NRZ) format.

Characters supported 7 or 8 data bits, even/odd/no parity, 1 or 2 stop bits.

RS232 connection provides full duplex operation as a DCE device with RTS/cts hardware handshaking – standard D9 connector.

RS485 connection provides half duplex operation for twisted-pair multidrop networks. Input and output buffers 2Kbyte

RS232 V.24 DCE 1.2 to 115.2 Kb/s RS485 1.2 – 230 Kbs RS232 V.24 DCE 1.2 to 115.2
Kb/s RS485 1.2 – 115.2 Kbs

Serial Server functionality provides multiple connectivity modes – serial to serial, serial to Ethernet, Modbus serial to Modbus TCP, and point to multipoint

Ethernet: N/A 10/100 BaseT RJ45, IEEE 802.3 compliant

Bridge/router functions work with all Ethernet protocols

Embedded protocols: TCP/IP, UDP, ARP, PPP, ICMP, HTTP, FTP, TFTP,
TELNET

10/100 BaseT RJ45, IEEE 802.3 compliant

Bridge/router functions work with all Ethernet protocols

Embedded protocols: TCP/IP, UDP ARP, PPP, ICMP, HTTP, FTP, TFTP, TELNET



Main menu 2

about seo